Archive | Wedding

Makin’ Loooooove… part 2 {DIY Marquee Letters}

***UPDATE***

We still get lots of comments/questions about these, so we made a video tutorial! Came up with some new tips that make the tricky parts wayyyy easier. Check out the video below!

You can also click here if you want to see the update tutorial in written form, or keep reading below to see the original one.

[Before we keep going, I want to pause and say if you have a sec it would mean SO much to us if you’d like our video or subscribe to our channel. We’re new to YouTube, so every view, like, and sub makes a huge difference for us. Thank youuuuu!]

***END UPDATE***

(Continued from part 1) There are a ton of great toys you can use for this next step… I mean… power tools… I used my jig saw. It’s a great wood/everything cutting power tool when you’re living in an apartment and don’t have a garage to store big toys. Soon to be fixed ^_^ (I’m sure there will be a post with a handyman garage setup).

DIY Marquee Letters- evanandkatelyn.com

Since we traced the letters in the previous post cutting them out was pretty easy. Remember, don’t push too hard or the edges will be rough and require more sanding. If you are unfamiliar with using a jig saw I would practice on some spare lumber. Also, since we bought our lumber before hand we planned the height of the letters so they would not require any cutting on the top and bottom. Before you know it you’ll have a masterly crafted letter in your hands:

DIY Marquee Letters- evanandkatelyn.com

Letters like the L are pretty easy to cut. No hard to reach corners. But when tight corners do arise don’t loose hope. Again, get some extra lumber and test to see how tight corners you can cut with whatever power tools you are using. With my jig saw I ended up doing a gradual turn and then backtracking to get that straight edge I wanted:

DIY Marquee Letters- evanandkatelyn.com

Before you know it you’ll have all your letters cut out! Good thing we remembered to take a picture when we were all done and not just partially so!!… not.

DIY Marquee Letters- evanandkatelyn.com

Whatever could we be spelling?! Live?!… umm can’t think of anything else but the other live… and love :)

Next we roll out the template again and gently hammer a nail in (somewhat of an oxymoron). Just nail it partially in to mark where you’ll be drilling later:

DIY Marquee Letters- evanandkatelyn.com

For the lights that we mentioned earlier a 13/16″ spade drill bit worked PERFECTLY! Just barely lets the light socket through. Make sure to measure a properly sized hole if you aren’t using our same lights. Run to your fav hardware store and pick up a your fav type of hole drill and have at it!

DIY Marquee Letters- evanandkatelyn.com

Follow the pattern you laid out earlier with your gentle nailing and you’ll do swell! Lay out your letters and admire your handiwork:

DIY Marquee Letters- evanandkatelyn.com

After you’ve made all the holes for your light bulbs, you’re gonna want to sand things down a bit. Because the plywood we got was pre-sanded, this part was pretty easy. We just did a few gentle swipes along the face of the letters and focused mainly on the edges using 220 grit sand paper.

Next came my favorite part… staining!! This was the first time we stained anything and it was awesome. Now we want to stain ALL THE THINGS! Before you go all stain crazy on your letters though, I’d recommend testing the stain on some scrap wood first. Again, we used Minwax stain in “Dark Walnut” (because we loved how it look on some projects over at Young House Love!)

DIY Marquee Letters- evanandkatelyn.com

We tested how the stain looked after sitting for 1 minute, 2 minutes, 5 minutes, and 10 minutes. When each section was done, we wiped things down with a clean old T-shirt. The visual difference between the stain times was pretty subtle so we decided to go with 1 minute. Hey, we are impatient!

DIY Marquee Letters- evanandkatelyn.com

Now it’s time to go to town on the letters! Make sure to wipe them down to get rid of dust and stuff first. Also, work somewhere well-ventilated. For us that meant our wittle teeny apartment balcony. Gotta work with what you’ve got! Also, remember to lay down a dropcloth or something to catch any drips. I read online that you’re supposed to apply the stain with the grain, so that’s what we did. The internet said so, so it must be true!

DIY Marquee Letters- evanandkatelyn.com

We didn’t worry too much about our edges because they won’t show once we add our metal sides. Also, by the time our minute of staining time was up almost all the stain was absorbed by the wood, but we still wiped off the little bit of excess with a clean old T-shirt.

Literally like 5 minutes later, we were done! Of course, you know we also had to pop some light bulbs in and test how they looked with the stained wood. One step closer to marquee-style letters for our wedding!

DIY Marquee Letters- evanandkatelyn.com

PS- Check out part 1: making the template, and part 3: attaching the metal siding for the full tutorial of this project! :D

Note: This post contains affiliated links. Thank you for supporting our blog!
DIY Marquee Letters- evanandkatelyn.com
11

Makin’ Loooooove… {DIY Marquee Letters}

***UPDATE***

We still get lots of comments/questions about these, so we made a video tutorial! Came up with some new tips that make the tricky parts wayyyy easier. Check out the video below!

You can also click here if you want to see the update tutorial in written form, or keep reading below to see the original one.

[Before we keep going, I want to pause and say if you have a sec it would mean SO much to us if you’d like our video or subscribe to our channel. We’re new to YouTube, so every view, like, and sub makes a huge difference for us. Thank youuuuu!]

***END UPDATE***

Makin’ loooove…letters! As in L.O.V.E, sheesh! Just look below and see what I mean…

DIY Marquee Letters- evanandkatelyn.com

We saw these marquee letters at a wedding expo and immediately thought they’d be awesome to have at our wedding. But renting them from a wedding decor company would be hella expensive, so my engineer fiance got to work! First we took some super precise measurements by taking a picture of my arm against the letters so we could eyeball the size later. You can tell by my expression that I totally did not feel awkward at all posing in the middle of the display.

DIY Marquee Letters- evanandkatelyn.com

Then we got home and got to work! We figured out from the above picture that we wanted them to be about 2 feet tall, and we went from there. We sorted through my library of 1,300+ fonts (I have a font problem… and I’m not ashamed) and picked one that suited us. Then we made a to-scale image in Photoshop. You can download it here if you’d like to use the font we used as a template.

DIY Marquee Letters- evanandkatelyn.com

The little circles are guides for where the light bulbs would need to go. Then we just printed it and boom- instant template!

DIY Marquee Letters- evanandkatelyn.com

When it came to supplies, we had to decide if we wanted to use wood, metal, foam core (that’s what most the online tutorials use), or something else. We ended up deciding on wood for the letters and metal for the siding. We found pre-sanded 2-foot-tall birch plywood that said “ready-to-stain” at Home Depot for $14 a pop. Sold! We picked up two of those, a roll of 6″ galvanized steel, some Minwax stain in “Dark Walnut” (because we loved how it look on Young House Love!) and a couple packs of outdoor lights.

We were just sort of wingin’ it and picking up what looked like it should work. We’ll do a full supplies list and cost breakdown at the end of things since I’m sure there will be more stuff we need to get along the way.

Next we cut out our letters, taped them together into something traceable, then laid them out on our plywood and traced away!

DIY Marquee Letters- evanandkatelyn.com

DIY Marquee Letters- evanandkatelyn.com

DIY Marquee Letters- evanandkatelyn.com

Once our letters were traced, it was time for the fun part- sawing! But this post has gotten pretty long, and Evan’s definitely the power-tool-wielding one in the relationship, so he’ll probably write about the sawing stuff. So for now we’ll end things here and pick back up later with part-2! On a side note, I should try to remember NOT to wear my super flattering XXL comfy pants when we’re taking pics for the blog… oh well!

PS- Check out part 2: cutting out and staining the letters, and part 3: attaching the metal siding for the full tutorial of this project! :D

Note: This post contains affiliated links. Thank you for supporting our blog!
DIY Marquee Letters- evanandkatelyn.com
65