Tag Archives | entryway

DIY Coat Rack

Hey guys! Today we’re gonna walk through how to make an easy DIY entryway coat rack, magnetic key holder, organizer shelf…. DIY thing to put your stuff on when you walk through the door.

You can check out the video above to see all the details, but we’ll also write out the basic steps below (the video shows it a little more clearly though!)

We’ve included plans for this project but it’s really customizable. You could make it any length you want, rearrange the shelves, have more or less hooks, etc, whatever best fits your space and needs. Have a tiny wall? Make a 2-ft version with one shelf. Got 8 kids? Well you’re gonna need a lot more hooks my friend. You get the idea.

DIY coat rack

This is a great project if you’re new to DIY and woodworking and don’t have a ton of tools. We just use two power tools and some basic supplies. See below for the full list of tools and materials, plus some optional stuff that will make things a little easier but aren’t 100% necessary.

TOOLS / MATERIALS:

OPTIONAL:

 Step 1: Make Circular Saw Jig (optional)

We made all our cuts with the circular saw, but lining up the blade can be tricky, so below is a quick tip if you want really accurate cuts.

DIY coat rack Make a jig using a scrap piece. Raise the blade so it doesn’t cut all the way through, clamp a speed square to the scrap, mark a line where the speed square is, and cut a groove. Now you have a guide that shows you where the blade will cut when you line up the speed square with the mark. We used this to line up our cuts.

DIY coat rack DIY coat rack DIY coat rack DIY coat rack Technically, instead of a groove you could just cut through the scrap piece, but the groove shows you the thickness of your cut.

Use the jig to mark where your speed square should be clamped, and clamp it to the piece you’re cutting.

Step 2: Make Your Cuts

We cut the 1×8 first, since it will make up the backing the runs the length of the entire organizer, and everything else will be based off that. For our space, we cut it to 35”, but you can make this length whatever you want.

DIY Coat Rack Then we cut two pieces of 1×4. We cut one piece to 24” for the higher shelf, and one to 9-¾” for the lower shelf. We wanted the shorter shelf to be wide enough to hold an envelope so we could put mail there, and we eyeballed what length we thought would look good for the longer shelf.

DIY Coat Rack We also cut a square ¾” dowel the same length as the shorter shelf to act as a shelf lip.

DIY Coat Rack DIY Coat Rack After our cuts, we gave everything a light sanding with fine grit sanding sponge (which we love BTW, since it’s flexible it wraps around wood corners easily).

DIY Coat Rack

Step 3: Attach Large Shelf

We didn’t do any fancy joinery for this build, everything is connected with countersunk screws placed in spots that won’t be seen.

DIY Coat Rack First we attached the long shelf to the backing. On the back of the backing, we traced out where we wanted the shelf to be and marked three points to drill through.

DIY Coat Rack First we drilled pilot holes through just the backing, not into the shelf. Then we clamped the shelf to the backing and used our pilot holes as guides to drill into the shelf. We used a countersink bit so our screws would be flush. Then we screwed through the backing and into our shelves.

DIY Coat Rack

Step 4: Add Magnets, Attach Small Shelf

We used a similar method (pilot holes – drill through pilot holes into piece you’re attaching – screw through pieces) to attach the dowel as a shelf lip to our shorter shelf. The lip shifted slightly as we attached it so it was a little off, but we sanded it down to even it out.

DIY Coat Rack DIY Coat Rack Before we attached the shorter shelf to our backing, we drilled shallow holes into the bottom of it to embed 3/8″ neodymium magnets. To know how deep to drill, we placed a magnet next to the bit and placed tape on the bit that marked the height of the magnet.

DIY Coat Rack DIY Coat Rack DIY Coat Rack

We used a couple drops of our favorite CA glue in the holes we drilled to attach the magnets. We also had a slight moment of panic because we didn’t have a hammer or mallet with us so we grabbed a nearby piece of 2×4 to pound the magnets in. It worked!

DIY Coat Rack DIY Coat Rack DIY Coat Rack

Step 5: Finishing

To finish, we stained the wood, did a couple coats of shellac, and a light coat of wax. At a minimum, we’d suggest doing the shellac because it gives it a nice sheen and some water resistance (a good thing to have if you’re hanging a wet raincoat).

DIY Coat Rack We used Minwax stain in “golden pecan” because we wanted a light color with warm undertones that still let the wood grain show through. We wiped it on with rags and wiped off any excess, then let it dry overnight.

DIY Coat Rack The next day we applied two coats of clear shellac with foam brushes, letting it dry an hour or so in between coats. Shellac raises the grain, so you need to sand after each coat.

DIY Coat Rack We had some 600 grit sandpaper so we used that, but you could probably use 320 if you have a reeeeeally light hand.

DIY Coat Rack Then we applied a thin layer of Briwax and buffed it out by hand with a shop towel. In the past, we’ve also buffed it out by placing a microfiber cloth under our orbital sander and doing that (link here if you wanna see that).

DIY Coat Rack DIY Coat Rack

Step 6: Adding Hardware

In terms of hardware, we added four hooks on the front and two sawtooth hangers on the back.

We got sawtooth hangers that attach to the piece with screws rather than tiny nails because it seemed more secure. We drilled small pilot holes into the backing and screwed in the screws by hand because we were pretty close to the edge.

DIY Coat Rack For hooks, we went with these bath towel hooks on Amazon. They’re only $11 for the set of four, whereas most coat hanging hooks used for this kind of thing would run you $20-$40 for four. Crazy! You screw them in from the front in a few places, cover the screws with a back place, and twist on the hook. Easy peasy.

DIY Coat Rack DIY Coat Rack DIY Coat Rack Don’t think this counts as hardware, but lastly we added little rubber feet to the back so it would hang straight and not scratch up the wall.

DIY Coat Rack

Step 7: Enjoy!

And that’s it! Hope you guys enjoyed this easy and flexible project. We’d love to see any variations you end up making so please tag us @evanandkatelyn on Instagram if you post any photos, and as always, let us know if you have any questions!

DIY Coat Rack DIY Coat Rack DIY Coat Rack DIY Coat Rack

………………………………………………………………
You can also find us at:

YouTube (all our DIY videos)
Instagram (sneak peeks @evanandkatelyn)
Patreon (if you wanna support us, but no pressure!)
Pinterest (stuff that inspires us)
Twitter (us, in 140 character doses)
Facebook (be our friend)
Instructables (straight up tutorials)

………………………………………………………………
Note: This post contains affiliate links. Thank you for supporting us!

0