Tag Archives | furniture

DIY 2×4 Side Table

We made this side table out of 2x4s for less than $9, which we think is pretty dang cool! We did it as part of the Modern Maker #two2x4challenge and it was definitely a challenge! You could make this table with other types of wood and the steps will be easier (2x4s tend to warp and pine is soft), but the cheap material allowed us to experiment with some joinery techniques we’d never done before. We learned a lot and shared lots of little tidbits (and failures!) in the video.

[Before we keep going, I want to pause and say if you have a sec it would mean SO much to us if you’d subscribe to our channel or share our video. We’re new to YouTube, so every view, like, and sub makes a huge difference for us. Thank you!]

DIY 2x4 side table for just $9 - Evan & Katelyn

We’ve included free plans that have a cut list and measurements. The video and this post will go into more details, but the plans are a great reference for the nitty gritty numbers. 

Here’s what you’ll need:

Materials:

Tools:

DIY 2x4 side table for just $9 - Evan & Katelyn

Squaring & the 2x4s

We started by giving our 2×4’s a nice square edge on all sides. The rounded edges they come with make it difficult to get a finished looking end product.

DIY 2x4 side table for just $9 - Evan & Katelyn We ran the top and bottom of them through the planer.

DIY 2x4 side table for just $9 - Evan & Katelyn Then we ran the left and right sides through the table saw, and then through the planer.

DIY 2x4 side table for just $9 - Evan & Katelyn We did this before cutting them to length because we thought that would make all our boards more consistent, but it was a little unwieldy running 10-ft boards through a table saw. So it might be easier to cut them first (leaving extra length that you can trim off later).

Cutting & making panels

After squaring them up, we cut the 2x4s to length for our top panel, shelf, and legs on our miter saw. You can find the lengths and cut list in the plans we linked to earlier.

DIY 2x4 side table for just $9 - Evan & Katelyn Everything got 10 degree miters: The legs are angled at 10 degrees, which means their ends need a 10 degree cut; and the shelf buts up against the legs so it therefore needs a 10 degree cut too. Technically, you could cut the top panel at 90 degrees but we thought 10 degrees would look nice, so that one is purely aesthetic.

DIY 2x4 side table for just $9 - Evan & Katelyn DIY 2x4 side table for just $9 - Evan & Katelyn Next we glued up the panels for our top piece and our shelf piece. We used Titebond Original wood glue here and Bessey clamps. We also have a little silicone brush that is awesome for applying the glue. We let these set overnight.

DIY 2x4 side table for just $9 - Evan & Katelyn DIY 2x4 side table for just $9 - Evan & Katelyn DIY 2x4 side table for just $9 - Evan & Katelyn Then we ran our two panels through the planer one more time to level out any unevenness from our glue up.

DIY 2x4 side table for just $9 - Evan & Katelyn Unfortunately, we got some snipe on the ends, which is when your board isn’t in contact with both rollers at the same time and the planer cuts the ends a little deeper.

DIY 2x4 side table for just $9 - Evan & Katelyn

We fixed this by running it through again and again with sacrificial boards in front of and behind it until we got rid of the snipe.

DIY 2x4 side table for just $9 - Evan & Katelyn

Cutting dados

This part was a little tricky since we’ve never cut dados before. We angled our table saw blade to 10 degrees and raised the blade so it would cut about halfway through the thickness of our boards. There are dados in a few different places: two in the underside of the tabletop for the legs to go into, and one on the inside of each leg for the shelf to sit in.

We started with the tabletop. We measured where the outside of each dado needed to be and made marks at those points. We started our cuts there and worked our way inward.

DIY 2x4 side table for just $9 - Evan & Katelyn We thought we’d widen our dado a little bit at a time and test fit the legs with each pass as we got close.

DIY 2x4 side table for just $9 - Evan & Katelyn DIY 2x4 side table for just $9 - Evan & Katelyn We tried to be careful, but we still cut our first dado a hair too big. Womp.

DIY 2x4 side table for just $9 - Evan & Katelyn We cut new legs for that side and it ended up being fine (you can’t visibly tell a difference in the leg thickness), but we did learn to stop a little early with our cuts. An extra snug fit is ok, and you can use a wood mallet to pound the wood into place if it’s tight. Luckily, our second dado under the tabletop was fine.

We tried to be careful, but we still cut our first dado a hair too big. Womp. Next we cut a dado on the inside of each leg. We actually did all the legs together to make sure the dados were consistent. We again used the method of marking where the dados needed to start and working our way down little by little.

DIY 2x4 side table for just $9 - Evan & Katelyn DIY 2x4 side table for just $9 - Evan & Katelyn To clean up our dados, we used a router with a ½” diameter dovetail bit and a chisel. The bit got the flat surfaces really well, and the chisel helped clean the corners (plus it was super satisfying).

DIY 2x4 side table for just $9 - Evan & Katelyn DIY 2x4 side table for just $9 - Evan & Katelyn

Assembly

With our dados cut, it was time to assemble. This table is put together with just wood glue, no screws involved. Unfortunately, when we started to assemble it we realized our shelf panel had warped a little.

DIY 2x4 side table for just $9 - Evan & Katelyn 2x4s are prone to warping, so if you use nicer wood you hopefully won’t have to worry about this happening as much. Luckily we were able to force it into place during our dry fit assembly.

However, it took us about 15 minutes to pound everything into place with that warped shelf, and our glue (Titebond III) has a set time of 10 minutes, so we literally had to race the clock for this assembly. If you don’t have any warping it won’t be as much of an issue.

DIY 2x4 side table for just $9 - Evan & Katelyn All the pieces need to be assembled simultaneously. We applied glue to our dados, roughly put the legs where they need to be in the tabletop dados, sat the shelf in the leg dados, and used a mallet to inch everything into place. We clamped everything together and let the glue dry overnight.

DIY 2x4 side table for just $9 - Evan & Katelyn DIY 2x4 side table for just $9 - Evan & Katelyn

Finishing

The next day, we unclamped our piece and gave the whole thing a good sanding using a random orbit sander for the large surfaces and sanding blocks to get into harder to reach spots.

DIY 2x4 side table for just $9 - Evan & Katelyn DIY 2x4 side table for just $9 - Evan & Katelyn Then we used wood filler at each joint to fill in any gaps we couldn’t close before the glue set. We let it dry and sanded it off.

DIY 2x4 side table for just $9 - Evan & Katelyn DIY 2x4 side table for just $9 - Evan & Katelyn Next we gave it two coats of shellac and sanded lightly with 600 grit sandpaper between coats. If you are too heavy handed with the sanding or use too low of a grit, you’ll sand the shellac right off.

DIY 2x4 side table for just $9 - Evan & Katelyn DIY 2x4 side table for just $9 - Evan & Katelyn DIY 2x4 side table for just $9 - Evan & Katelyn After the shellac, we gave it a coat of Briwax, which we then buffed off by placing a microfiber rag between our random orbit sander and the table. The finish came out reeeeally nice. It’s got some shine but isn’t overly shiny, and it feels super smooth.

DIY 2x4 side table for just $9 - Evan & Katelyn DIY 2x4 side table for just $9 - Evan & Katelyn DIY 2x4 side table for just $9 - Evan & Katelyn

Done!

We love how this side table turned out! Like we said earlier, this build would probably be easier with nicer, more expensive wood, but this was a great challenge and the cheap material really allowed us to experiment with some new techniques. Please let us know if you have any questions about this build. Thanks!

DIY 2x4 side table for just $9 - Evan & Katelyn DIY 2x4 side table for just $9 - Evan & Katelyn DIY 2x4 side table for just $9 - Evan & Katelyn DIY 2x4 side table for just $9 - Evan & Katelyn ………………………………………………………………
You can also find us at:

YouTube (all our DIY videos)
Instagram (sneak peeks @evanandkatelyn)
Patreon (if you wanna support us, but no pressure!)
Pinterest (stuff that inspires us)
Twitter (us, in 140 character doses)
Facebook (be our friend)
Instructables (straight up tutorials)
………………………………………………………………
Note: This post contains affiliate links. Thank you for supporting us!

2

IKEA MALM dresser hack

Today we’re going to show you how we used $35-per-dresser worth of hardware to upgraded a couple IKEA Malms that until recently, looked like this:

DIY Dresser Upgrade And now… it looks like this!

You can watch the video that covers everything below, or keep scrolling for all our choices, steps, and tips in blog-format.

[Before we keep going, I want to pause and say if you have a second it would mean SO much to us if you’d like our video or subscribe to our channel. Since we’re brand new to YouTube, every view, like, and subscription makes a huge difference for us. Click here to see the whole channel. Thank youuuuu! We’re doing a big goofy happy dance right now!]

We were inspired by this discontinued West Elm Dresser to do knobs on the top row of drawers and pulls on the rest. If you want to check out the backstory and challenges we faced about hardware and dressers (riveting, I know) before I get to the actual tutorial, click here to read our last post.

West Elm copycat IKEA hack, DIY dresser upgrade using knobs and pulls - evanandkatelyn.com This ended up being a really simple tutorial that you could definitely tackle on a weeknight after work with just a few tools. Below is what we used:

Materials

West Elm copycat IKEA hack, DIY dresser upgrade using knobs and pulls - evanandkatelyn.com Tools

We also ended up needing bolt cutters, a wrench, and a spare nut that fit onto our screw because we ran into a little snag with our screw length (more details on that later).

West Elm copycat IKEA hack, DIY dresser upgrade using knobs and pulls - evanandkatelyn.com The first thing you have to do it make a big mess of your room by emptying all your drawers. Just think of it as an opportunity to get rid of that Panic at the Disco t-shirt that’s been shoved in the back for years.

West Elm copycat IKEA hack, DIY dresser upgrade using knobs and pulls - evanandkatelyn.com Then you’ll need to measure your drawers and mark each spot to drill for your hardware. Double check your measurements because having a bunch of mistake-holes in your dresser is a good way to ruin it.

West Elm copycat IKEA hack, DIY dresser upgrade using knobs and pulls - evanandkatelyn.com For the pulls, we measured the width of the drawer front, then the width between the two holes in each pull. We subtracted the pull-width from the drawer-width and divided that number in two, which told us how far we needed to measure from each side of our drawer. We centered those marks vertically.

West Elm copycat IKEA hack, DIY dresser upgrade using knobs and pulls - evanandkatelyn.com The knobs were easier. We just eyeballed what positioning looked good, made sure they were equally spaced width-wise from the outside edge of the drawer, and centered those vertically too.

West Elm copycat IKEA hack, DIY dresser upgrade using knobs and pulls - evanandkatelyn.com We recommend placing your hardware on each drawer front where you’ve marked before you drill. This gives you a visual check of how you did. When you feel confident that your ability to do simple math has resulted in the correct placement of your hardware, it’s time to get out the drill.

West Elm copycat IKEA hack, DIY dresser upgrade using knobs and pulls - evanandkatelyn.com To pick the right bit size, you can hold your screw up to several different sized bits and pick one that is just a hair thicker than your screw.

West Elm copycat IKEA hack, DIY dresser upgrade using knobs and pulls - evanandkatelyn.com West Elm copycat IKEA hack, DIY dresser upgrade using knobs and pulls - evanandkatelyn.com We really like using a drill guide (that little metal bar we’re drilling through) to help us drill straight down (instead of at an angle). If you’re nervous about drilling through perfectly good furniture, I highly recommend getting one of these little guys.

West Elm copycat IKEA hack, DIY dresser upgrade using knobs and pulls - evanandkatelyn.com After drilling, we did hit a bit of a snag. See, hardware will typically come with screws, and ours came with two different screw size options. But sadly, we had a Goldilocks moment and one was too long and one was too short, but neither was juuuust right.

West Elm copycat IKEA hack, DIY dresser upgrade using knobs and pulls - evanandkatelyn.com This is a common issue to run into, so we’re going to share a little tip (so you can avoid going to Home Depot for the 10th time that day to pick up new screws).

Grab a set of bolt cutters and a nut that’s sized to fit your screw. Thread the nut onto the screw, then cut the too-long screw to  the length you need.

West Elm copycat IKEA hack, DIY dresser upgrade using knobs and pulls - evanandkatelyn.com West Elm copycat IKEA hack, DIY dresser upgrade using knobs and pulls - evanandkatelyn.com West Elm copycat IKEA hack, DIY dresser upgrade using knobs and pulls - evanandkatelyn.com Cutting it will deform the threads slightly, but that’s where the nut comes in. Grab the nut with a wrench and use your screwdriver to back the screw out of the nut. As you rotate it off over the damaged threads, it will re-shape them back to normal and boom, you have a perfectly-sized screw!

West Elm copycat IKEA hack, DIY dresser upgrade using knobs and pulls - evanandkatelyn.com West Elm copycat IKEA hack, DIY dresser upgrade using knobs and pulls - evanandkatelyn.com The next step is to simply attach your hardware with your screws. You can use a normal screwdriver or a powered screwdriver depending on what you have.

West Elm copycat IKEA hack, DIY dresser upgrade using knobs and pulls - evanandkatelyn.com Then just add your drawers (I guess you can put your clothes back now too) and give yourself a high five because you’re done!

West Elm copycat IKEA hack, DIY dresser upgrade using knobs and pulls - evanandkatelyn.com This project really was super easy, and it ended up only costing us $35 per dresser. In my book, that is WAY better than dishing out hundreds (or even thousands!) on something new.

West Elm copycat IKEA hack, DIY dresser upgrade using knobs and pulls - evanandkatelyn.com Before…

DIY Dresser Upgrade After!

………………………………………………………………
You can also find us at:

YouTube (all our DIY videos)
Instagram (sneak peeks @evanandkatelyn)
Patreon (if you wanna support us, but no pressure!)
Pinterest (stuff that inspires us)
Twitter (us, in 140 character doses)
Facebook (be our friend)
Instructables (straight up tutorials)
………………………………………………………………
Note: This post contains affiliate links. Thank you for supporting us!

 

1

Knobs, pulls, and dressers, oh my!

Hey guys! If you know me, you know I can go a little overboard when I go into research-mode. Sometimes it makes sense, like researching everything thoroughly before we swapped out some plumbing or blew our own insulation. But sometimes, I’ll spend hours upon hours researching something really trivial, like knobs.

Real quick spoiler alert: if you wanna see how these dressers turned out, watch the video below! And read the full tutorial here.

It all started when the IKEA Malm dressers got recalled for a tipping hazard. We have two of these in our bedroom, and IKEA gave everyone the option of handing them over in exchange for a full refund.

Dresser and hardware inspiration - evanandkatelyn.com

So I was like yay, an excuse a chance to upgrade our dresser AND get $200 back! I started an online hunt to find the perfect new dressers, with these requirements in mind:

  1. Something at least as large as our current eight-drawer double-Malm set up.
  2. Nicer quality than our current dressers (otherwise, why upgrade?)
  3. Within the price range we felt comfortable spending.  

Apparently, I am a very unreasonable person, because we didn’t find anything that met all three of those needs. We could find something that met 1 and 2, or 1 and 3, or 2 and 3, but nothing that made the clouds part and the dresser heavens sing.

So I had to accept that functionally-speaking, we really had no complaints about our Malms, and the day for a dresser upgrade was not this day. Womp.

But here’s where the story takes an upturn. I decided as a consolation prize, I’d upgrade our current dressers with some new hardware. This launched me down a knobs-and-pulls rabbit hole that posed some challenges because:

  1. I wanted to do a mix of knobs AND pulls, inspired by this West Elm dresser (which is sadly no longer available). This meant I couldn’t just buy eight of the same thing for our eight drawers: I had to find six pulls and four knobs, and they had to match.
  2. I wanted gold/brass hardware to match the gold deer head and gold art in our bedroom gallery wall. Plus, I think gold always warms up black (and I prefer a warmer black to a cooler black). Despite its growing trendiness lately, gold hardware still has a smaller selection online than other finishes.
  3. Hardware can get expensive (think $16 a pull and $8 a knob, on the mid-priced end) and the dressers themselves were only $100 each, so it seemed weird to spend tons of money on hardware.

Dresser and hardware inspiration - evanandkatelyn.com

Again, tons and tons of research was done (how are there so many knobs in the world??) but eventually I emerged victorious! I found these knobs and these pulls, did a big ol’ happy dance, and asked for them for Christmas (that’s a normal present to ask for… right?). Spoiler alert – I got em! So keep your eye out for a soon-to-be-posted tutorial on our dresser makeover.

Dresser and hardware inspiration - evanandkatelyn.com

In the end I’d say this is a win, even though I mayyyy have lost a little sleep (and several hours of my life) to researching bedroom furniture. So instead of having all that research go to waste, I’m sharing it at the end of the post here. Hopefully, it will prevent some of you from spending as much time as I did in Dresserville and Knobs-and-Pulls-City. Below are our final contenders, and I’ve included all the important information we compared.

Dressers we liked

West Elm Logan dresser in acorn
$899, 58″w x 18″d x 32″h, solid wood base + wood veneer finish

Dresser and hardware inspiration - evanandkatelyn.com

This one was so pretty and we really loved the warmth of the wood, plus the price seemed reasonable for something so nice, but it wasn’t as big as our old set up and we couldn’t afford to have less storage than before.

West Elm Logan 6-Drawer Dresser
$936, 58″w x 18″d x 32″h, solid wood base + wood veneer finish

Dresser and hardware inspiration - evanandkatelyn.com

Love the mix of wood and metal on this one! Price still wasn’t too bad, though same issue with storage – it just wasn’t quite big enough,

IKEA Hemnes 8-Drawer Dresser
$249, 63″w x 19 5/8″d x 37 3/8″h, particle board
Dresser and hardware inspiration - evanandkatelyn.com

The price was right and the size was much better for this dresser, but we weren’t sure if we wanted to buy another IKEA dresser since we already had one we liked well enough. But if you’re looking for a large, inexpensive dresser, I love the lines and double top drawers on this one.

Munich 6 Drawer Double Dresser
$339, 59.29″w x16.5″d x32.75″h, particle board

Dresser and hardware inspiration - evanandkatelyn.com

This one gave us similar vibes as the West Elm Logan with the mix of metal and wood tones. As usual, same problem in that it wasn’t quite big enough for us, but we still think this is a great dresser that looks pricier than it is.

Hardware we liked

Dresser and hardware inspiration - evanandkatelyn.com

01. CB2 hex brushed brass drawer pull
$4.95 each. I LOVED the look of these, and generally I love hexagons, but we always end up choosing the geometric design so I wanted to try something different.

02. All Modern QMI cone novelty knob
$4.24 each. Good price and nice, tiny, and simple.

03. Liberty Artesia knob
$5.18 each. Really cool look, but in the end I wanted something with a bit of curve to balance the straight pulls.

04. Kohler Purist/Stillness cabinet knob
$12.30 each. The most classic design, but a little pricier.

Pulls we liked

Dresser and hardware inspiration - evanandkatelyn.com

01. Amerock Manor cup pull
$14.05 each (plus shipping). These were really cool and I love the look of a cup pull, but they were a little more than we wanted to spend since we needed six of them.

02. Skylight Bar Pull
$15.99 each. Again, a little pricey since we needed so many… but I love the way these look!

03. Hampton Collection bar pull
$7.95 each. Another pretty option, especially if you’re looking for a warmer toned gold.

04. Hickory Hardware Metropolis center bar pull
$7.84 each. Another solid option for a great price.

Hope this post helps someone else in their search for the perfect dresser/dresser upgrade!

Note: This post contains affiliated links. Thank you for supporting our blog!
2

DIY Butcher Block Dining Table

Hey y’all! You may have seen on our Instagram recently a post about what the heck we did to our dining table. If you haven’t seen it, here’s a hint: it involved drawing all over and drilling holes into a perfectly good West Elm Parsons table (side note, I think we have an older version because ours is longer than what’s online).

DIY Butcher Block Dining Table - evanandkatelyn.com Are we crazy? A little. Justifiably crazy? I think so! Because the end result of everything was this!

DIY Butcher Block Dining Table - evanandkatelyn.com But I’ll backtrack a bit and explain how we got here. First off, yes our table was perfectly good. It is SUPER sturdy, has a leaf which made it usable in both our little apartment and our current larger dining room, plus it’s lovely and simple and modern.

DIY Butcher Block Dining Table - evanandkatelyn.com BUT we got it secondhand. And the previous owner had abused it with a combination of things-that-were-too-hot and things-that-were-too-wet. So the oak veneer surface was looking pretty rough. I’ve circled some of of the trouble spots below.

DIY Butcher Block Dining Table - evanandkatelyn.com The damaged parts have continued to get worse over time, and we knew eventually we would need a new table. Because our issues stemmed from veneer, we reeeeeally had our hearts set on solid wood. But as you know… Solid wood tables cost an arm, a leg, your first born, and your entire collection of Pokemon cards. Specifically I had my eyes on the Blu Dot Branch table that Chris and Julia are rocking. The light wood top and black metals legs had me all googly eyed, but the $1600 (+ shipping + tax) price tag did not. So I put the solid wood dream temporarily out of my mind.

Then one weekend we found ourselves enjoying $2 hot dog and drink combos at IKEA on an un-table-related trip, and we saw that they have a couple solid wood tables at really good prices (in the $380-$450 range). Ring ring, it’s your hopes and dreams of a solid wood table calling back! Here and here are a couple we saw.

But after some measuring and test-sits, we realized that none of them could fit as many people as our current table, which wasn’t going to work for us. We felt kinda bummed until we made our way to the kitchen area and saw Hammarp butcher block in solid beech on clearance ($49 for the 72″ pieces and $69 for the 98″ pieces)!!!!! Wheels started turning. Could we have the solid wood table top we wanted and whatever size our hearts desired?!?!?

Naturally, we bought the entire remaining stock.

Haha, that sounds way crazier than it is. We actually have several projects in mind that could use butcher block (we’ve already used it once for Evan’s desk – we owe you a post on that!) and the “entire remaining stock” was five pieces of the 98″ length. Sorry everyone else in the Houston area. IKEA is fresh out of Hammarp beech.

DIY Butcher Block Dining Table - evanandkatelyn.com We actually had friends coming over for dinner that night so we couldn’t construct the new table quite yet. Butcher block needs to be treated before it’s safe from spills and such. We didn’t feel confident in the neatness of ourselves or our friends when spaghetti sauce is involved, so we decided to start the sealing process before the butcher block was attached to anything. We picked up some of those painting pyramids (how have we gone so long without them?!?) and spaced them out the length of the butcher block, then laid the butcher block on top of them.

DIY Butcher Block Dining Table - evanandkatelyn.com We did some research and found that there are basically two options when it comes to sealing butcher block: Waterlox or a mineral oil mix. Waterlox is a little more hardcore: if you stain your butcher block you have to use it to make it food safe, and it’s also very waterproof, but it’s harder to apply. Mineral oil is easier and cheaper, but not as immediately waterproof (it takes lots of applications and builds up more of a seal over time). Since our butcher block was for our table, not near a sink or where food would be prepped, we opted for a mineral oil product. Specifically, this one:

DIY Butcher Block Dining Table - evanandkatelyn.com It’s called The Natchez Solution Complete Furniture Care. It’s got mineral oil, beeswax (which helps fill any little imperfections in the wood) and lemon oil (which helps bring out the natural luster of the wood). It goes on smoothly and has a consistency like… salad dressing? Haha not as liquidy as water, but thin enough to be spread. And it really does make a HUGE visual difference in the look of the wood! In the photo below you can see the difference between wood that’s been oiled and wood that hasn’t.

DIY Butcher Block Dining Table - evanandkatelyn.com The whole process was really painless. Plus the oil smells nice :)

DIY Butcher Block Dining Table - evanandkatelyn.com

DIY Butcher Block Dining Table - evanandkatelyn.com While I worked on treating the wood, Evan got started doing the scary part:

DIY Butcher Block Dining Table - evanandkatelyn.com So here was the general plan – instead of buying new legs for our butcher block or removing the legs from our current table and using those, we decided to just put the butcher block directly onto the old table. Almost seemed too easy to work haha. So to do this, we needed to:

  1. Draw out guidelines on the old table for placement of the butcher block.
  2. Drill holes through our table (eek!).
  3. Place butcher block along guidelines, and mark through the holes onto the butcher block.
  4. Where we marked, add T-nuts into the butcher block.
  5. Replace butcher block onto table along guides and screw through the holes into the T-nuts.

1.  DRAW GUIDELINES

Not gonna lie, drawing all over our table was a little nerve wracking. It was that once-we-do-this-we’re-committed moment.

DIY Butcher Block Dining Table - evanandkatelyn.com We drew one line along the center of our table length-wise, and drew two more lines halfway between the center and the edge.

DIY Butcher Block Dining Table - evanandkatelyn.com The center mark was where our two butcher blocks would meet. Our table was 96″ x 38″, and each butcher block was 98″ x 25″, so we needed two. I made a couple illustrations below to show what the plan was.

DIY Butcher Block Dining Table - evanandkatelyn.com 2.  DRILL THROUGH TABLE

X marks the spots we drilled in the illustration above. We did have to adjust slightly to avoid hitting some of the leaf hardware, but the adjustments were minor and we still stayed pretty close to the line. This was the scariest part! By the way, our awesome Dewalt 20v drill was Evan’s best friend during this project. We use it FOR SO MANY PROJECTS and it’s a powerhouse. If you’re in the market for a drill, we HIGHLY recommend it.

DIY Butcher Block Dining Table - evanandkatelyn.com DIY Butcher Block Dining Table - evanandkatelyn.com To keep the drill bit going straight down and not at any funky angles, Evan used this V-drill guide. It’s suuuuper handy. We used it to help us drill all four holes.

DIY Butcher Block Dining Table - evanandkatelyn.com 3. PLACE AND MARK BUTCHER BLOCK

In this step we used our guidelines to place the butcher block centered on the table. We had about 6 inches of butcher block overhanding each side width-wise, and about 1 inch on each side length-wise.

DIY Butcher Block Dining Table - evanandkatelyn.com Evan got under the table and put some white paint from our paint pen (the same one we used to mark up the table) on the end of his drill bit. He poked it through the holes we drilled in the table and onto the butcher block sitting on top of the table.

DIY Butcher Block Dining Table - evanandkatelyn.com DIY Butcher Block Dining Table - evanandkatelyn.com Hehe. He’s cute :)

4. ADD T-NUTS TO BUTCHER BLOCK

We pulled the butcher block off the table and placed it bottom-side-up on the floor so we could see the paint marks Evan left. Then he measured the depth of our T-nuts and marked that depth on the drill bit so we could drill holes to the perfect depth.

DIY Butcher Block Dining Table - evanandkatelyn.com For those who don’t know, these are T-nuts, which are fasteners that have internal threading you can screw into. We could have just screwed into the butcher block directly, but we knew when we move we might have to remove the table top to make it more portable. Unscrewing and re-screwing into the same hole can eventually weaken the grip you have. These metal internal threads won’t deteriorate like screwing directly into wood would.

So to add the T-nut, Evan first created a recessed area for it to snuggly sit so that it was flush with the bottom of the wood. To do this he used a forstner bit that was the same diameter as our T-nut’s diameter. He also drilled a small pilot hole into the center of the recessed area.

DIY Butcher Block Dining Table - evanandkatelyn.com Next he used his drill with the marked bit to drill the correct depth for the T-nut. That cylinder in the middle of the T-nut is where the internal thread is, and that goes into the hole we drilled (the teeth grip it in place). You can see in the photo below how he stopped right at the paint mark.

DIY Butcher Block Dining Table - evanandkatelyn.com Evan sprayed the T-nut with super glue accelerant (which is amazing by the way… it makes super glue set INSTANTLY) and then applied super glue to the T-nut and pressed it into the hole. The super glue was an optional step to make things even more secure, but you wouldn’t necessarily have to do it.

DIY Butcher Block Dining Table - evanandkatelyn.com To get the teeth of the T-nut to dig in, you whack it with a hammer while having way too much fun not being still enough for your wife to take a photo :P

DIY Butcher Block Dining Table - evanandkatelyn.com Here’s how it looks when it’s in:

DIY Butcher Block Dining Table - evanandkatelyn.com 5. ATTACH BUTCHER BLOCK VIA T-NUTS

Almost done guys! The last step was to replace the butcher block on our table, once again aligning with our guidelines and making sure the T-nuts aligned with the holes we drilled in the table earlier. Evan drilled through the holes and into our T-nuts, adding a washer to distribute the force of the screw. He did this through all four holes in the table, so each butcher block was attached at two points.

DIY Butcher Block Dining Table - evanandkatelyn.com That’s the last step! Then we stepped back and admired our beautiful solid wood table top.

DIY Butcher Block Dining Table - evanandkatelyn.com We weren’t sure initially how we’d feel about size of the table, since it’s significantly wider now than it used to be. But we don’t mind the overhang of the wood and actually REALLY love how much of a statement the extra big table top makes.

DIY Butcher Block Dining Table - evanandkatelyn.com We feel like overall it brightens up the space SO much. It was crazy to see our space go from this:

DIY Butcher Block Dining Table - evanandkatelyn.com DIY Butcher Block Dining Table - evanandkatelyn.com To this:
DIY Butcher Block Dining Table - evanandkatelyn.com DIY Butcher Block Dining Table - evanandkatelyn.com
Also we don’t feel like we need a runner anymore. We tried it with the runner but opted to go without it and just place a few simple faux plants (and super cheap planters) from IKEA along the center. The wood is so pretty, it really doesn’t need much on top of it.

After the first few coats of oil soaked in, we had our first dinner on it to make it official!

DIY Butcher Block Dining Table - evanandkatelyn.com We are pretty much enamored with our upgraded table. I like to walk by and pet it with hearts in my eyes. It’s true love!

BUDGET BREAKDOWN

(2) 98″ Hammarp butcher block in beech: $69.99 (x2)
(4) T-nuts: ~$1 (x4)
(1) Forstner bit: $7.89
(1) Natchez Solution: $15.95
(1) set of painting pyramids: $4.97 (optional)
Drill, bits, screws, washers, V-drill guide, super glue + accelerant, and badass skills already owned.

TOTAL = $172.79

Much cheaper than even the IKEA-level wood tables… and insanely affordable compared to any other solid wood table we found, especially considering how large it is. We are super proud of this and couldn’t be happier with how it turned out. Have you guys used butcher blocks in any projects? We have a few extras and we can’t wait to decide how to use them, so we’d love to hear what you’ve done!

Note: This post contains affiliated links. Thank you for supporting our blog!
0

Caster Coffee Table

As y’all know, we recently turned our former workout room into Evan’s new office. Which is great for Evan’s goal of having a functional workshop, but not so great for our goal of working out on a semi-regular basis.

As much as part of us would like to say “oh no, guess we can’t work out so we’ve gotta binge watch Steven Universe instead,” we know we’ve gotta have a space to work out in. And I work out to YouTube videos, so it needed to be a space with a TV. Our living room was the logical answer. We’ve got a nice big space in front of our TV on the rug, but unfortunately a super heavy storage coffee table sits in the middle of that. So we decided to make that super heavy storage coffee table mobile.

Adding casters to our coffee table - evanandkatelyn.com

We looked at different types of casters we could add, but because the base our table sits on is smaller that the size of the top, we didn’t want something that would raise it up and potentially make it topple over easily. Plus we didn’t feel like the look of traditional casters would look great with the style of this table. So we opted for roller ball transfer bearings that would sit as flush as possible to the underside of the table.

bearing

And wow… it was so easy. We just removed the storage drawers, turned the table upside down…

1-dissassemble-and-flip-c

screwed the four casters into the four corners through the holes in their plates…

2-mark-and-drill-c

flip and mess around with it (not necessary, but recommended)…

3-flip-and-play

and re-assemble!

4-re-assemble

It’s super functional and easy to roll out of the way when we need to workout, yet it still feels really sturdy and it didn’t change the look of our table. Now we want to add casters to ALL THE THINGS. Bench in our entry way? Casters. How about our desks? Casters. Mochi’s litter box? Casters.

Adding casters to our coffee table - evanandkatelyn.com

Cheers to a quick, easy, and super functional project.

8

Couch Buying Trick

Evan and I have been doing a lot of couch shopping. Anyone who’s been to our place knows how incredibly comfy our current couches are. And anyone who’s been to our place has also heard me comment about how manly they are. They are THE ultimate man couches. As much as I tried to soften them up with pillows and fluffy blankets, there was no hiding the manliness.

Couch Buying Trick- evanandkatelyn.com Couch Buying Trick- evanandkatelyn.com

As comfy as they are, they’re a little beat up and somehow feel bulkier here in the house than they did in the apartment. Maybe it’s because they’re floating now instead of being against walls. Maybe it’s because I’ve been staring at them for too long. But either way, we decided to buy a new couch!

The issue Evan and I have with couch shopping is that he’s big and I’m little. Couches that suit me don’t fit him, and couches he likes swallow me up. Also, he was more willing to sacrifice looks for comfort, and I was more willing to sacrifice comfort for looks. Like buying those heels that are super cute but destroy your ankles. But the good news is we both knew we wanted a modern grey sectional. And finally, while browsing Crate & Barrel, we found it.

lounge-2-piece-sectional-sofa

Isn’t he a good looking couch?? It’s the Lounge 2-piece sectional in “Cement.” The thing we liked most is that we could both sit on the chaise with elbow room to spare! To get an idea of the scale, here’s a picture I snapped when we first tried it out in the store.

Couch Buying Trick- evanandkatelyn.com

Evan was instantly sold. I was a little nervous though. It was so big! The cushions are 46″ deep!! It’s a beast of a couch. A wonderful, comfy, giant, modern beast. Visually, it looked like the overall footprint when paired with an ottoman (which we plan to do) was too square for our rectangular rug.

Since I was worried about how it would fit, when we got home we devised this little trick to help visualize a couch (or really any type of furniture!) in your home.

We got the measurements of the sectional and ottoman, moved our current couches our of the way, and grabbed our masking tape and measuring tape.

Couch Buying Trick- evanandkatelyn.com

First, use the measuring tape to mark corners of your couch with a piece of masking tape, using measurements listed on the item specs (you can usually find these online). We lined up the back of the couch with the back of the rug and centered it. Our rug is 12 feet (144″) wide and the sectional is 124″ wide, so we had 10″ of rug space on either side.

Couch Buying Trick- evanandkatelyn.com

Cat’s are really good at helping with this part.

Couch Buying Trick- evanandkatelyn.com

Once all your corners are marked, connect the dots with masking tape.

Couch Buying Trick- evanandkatelyn.com

Couch Buying Trick- evanandkatelyn.com

If you have matching outfits and temporary tattoos that step works even better.

Then marvel at your imaginary couch! To my surprise, the measurements fit PERFECTLY on our rug and we still had room for our coffee table. I was sold!

Couch buying trick evanandkatelyn.com

So there’s our little trick! Even if you think you can picture a piece of furniture in your house, it wouldn’t hurt to spend a couple minutes with some masking tape to double check how it will actually fit. Anyone else have any tips or tricks for furniture buying? We are still kinda winging it so if you’ve got any tricks up your sleeve, spill!

………………………………………………………………
You can also find us at:YouTube (all our DIY videos)
Instagram (sneak peeks @evanandkatelyn)
Patreon (if you wanna support us, but no pressure!)
Pinterest (stuff that inspires us)
Twitter (us, in 140 character doses)
Facebook (be our friend)
Instructables (straight up tutorials)
………………………………………………………………

28